Day Night Sensor using Contactor wiring | Day night sensor wiring

Day-Night Sensor using contactor wiring:

This diagram shows how to make Day Night Sensor using Contactor wiring. Day-night sensor wiring. In this circuit, we use a DP MCB ( Double Pole Miniature Circuit Breaker), a Magnetic contactor, a Day Night Sensor, and 3 lights. First, we need to connect DP MCB then connect the magnetic contactor, then connect the day-night sensor, then connect the lights with the magnetic contactor. Now this circuit is ready for use. If you want to know more about this circuit please check our youtube video below the post.

Diagram of day-night sensor wiring:

Fig 1: Day Night Sensor using Contactor wiring

Components Need for this Project:

You can get the components from any of the sites below:

1. DP MCB [See Buy Click Amazon]
2. Contactor [See Buy Click Amazon]
3. Day-night Sensor [See Buy Click Amazon]
4. Light [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

• Fan in Regulator Wiring Diagram | Connection of fan regulator

• Ampere meter in voltmeter wiring | Wiring Voltmeter and amp Meter

• Electrical Panel for Exterior Light Wiring

• Emergency Stop Flash Using Emergency Alarm Wiring

• Single Phase Meter Connection | Electrical Meter Wiring Diagram

Components used to make the Day-night sensor wiring:

01. DP MCB

Fig 2: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

02. Contactor

Fig 3: Contactor

A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC)

03. Day-night Sensor

Fig 4: Day-night Sensor

An Automatic Day Night Light Sensor Switch can Switch on Any Electrical Device Automatically When Dark Falls And Switch off in the Morning Automatically. This Night light With an Energy-Efficient LED (Light Emitting Diode) can be Plugged into the Socket and has a light sensor so that the lamp switches on automatically when it gets dark. This is a Photo Technology-Based automatic sensor switch for 220V AC mains, which can be Widely Used in Street Lights, Factories, Gardens, Shops, Etc., and Other Places for Automatic Lighting. Turns ON the Light in the Dark & Turns OFF in The Light.

04. Light

Fig 5: Light

CFLs work in a completely different way from ordinary lamps, they work by using a different process called fluorescence rather than generating light from heat. A typical light bulb wastes 90% of energy and converts only 10% of energy into light, this is where CFL has the biggest advantage. CFL- Curved or conical glass tube filled with argon and a small amount of mercury vapor. The inner wall of the glass is coated with fluorescent material. CFL- It is manufactured using the principle of creating fluorescent light. CFL- Originally white in color but now the construction and use of CFLs producing colored light has become popular.

Thank You for visiting the website. Keep visiting for more Updates.