Single Phase Hair Wiring Connection | hair dryer coil repair

Single Phase Hair Wiring Connection:

This Diagram Shows SCR Elektroniks make CORD Swiveling Test Set UP For Hair Dryers & Hair Straighteners is used to test the Electrical Accessories/Appliances for their Mechanical strength. Operate Appliances Hair dryer or Hair Straightener at Rated Voltage. Rotate the Appliance Around its Major axis,20 Revolutions Clockwise & 20 Revolutions anti-Clockwise.

Diagram of Single Phase Hair Wiring Connection wiring:

Single Phase Hair Wiring Connection
Fig 1: Single Phase Hair Wiring Connection

Components Need for this Project:

You can get the components from any of the sites below:

  1. Haire Dryer [See Buy Click Amazon]
  2. Blower DC Motor [See Buy Click Amazon]
  3. Diode [See Buy Click Amazon]
  4. Switch [See Buy Click Amazon]
  5. Two Pin Plug [See Buy Click Amazon]
*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

Read Also:

Components used to make the Single Phase Hair Wiring Connection:

01. Haire Dryer

Haire Dryer
Fig 2: Haire Dryer
Hot liquid or air is lighter than cold air or liquid. Again, water or air is a poor conductor of heat. Now, if they are heated from the floor, a convection current (didn't remember the bungalow.) is created. This causes hot fluid or air to rise and push the relatively cold air or fluid down. Now, if the heating element of a rice cooker were placed upwards instead of downwards, the water on the submerged rice would boil very quickly, but the rice would remain cold and uncooked. Even if the water above boils and evaporates, rice will not be produced. So the element stays down, and so does the power connection.

02. Blower DC Motor

Blower DC Motor
Fig 3: Blower DC Motor
A DC Motor is a device that Converts Electrical energy into Mechanical Energy. A DC motor usually accepts a DC source and converts it into mechanical energy, hence it is called a DC motor. A motor in which a series field coil is connected to the armature is called a series motor. The torque of a series motor depends on the armature current, and field strength. A motor in which the field coil is connected in parallel with the armature is called a shunt motor. The torque of a shunt motor depends on the variation of mains field strength and armature current.

03. Diode 

Fig 4: Diode
The word diode is a combination of two words, 'die' and 'electrode' so we can generally say that an electronics component having two electrodes is a diode. Diode or rectifier is used in various ways in electronics. However, the main and main function of a diode or rectifier in electronics is to convert AC current into DC current and make the current constant. And this process of converting current AC to DC is called rectification. When current is supplied to the diode, it cannot return because the diode has negative to positive, denoted by P and N. P means anode positive RN means cathode negative.

04. Switch

Fig 5: Switch 
A Single-Pole, Single-Throw (SPST) Switch. It's Got one Output and One Input. The Switch will Either be Closed or Completely Disconnected. SPSTs are Perfect for on-off Switching. They're also a Very Common Form of Momentary Switches. SPST Switches are Commonly Used in a Variety of Electrical Circuits and Applications, Such as Turning on And off Lights, Fans, and Other Appliances. They can Also be Used to Control the Flow of Electricity to Different Parts of a Circuit or to Switch Between Different Circuits Altogether.

05. Two Pin Plug

Two Pin Plug
Fig 6: Two Pin Plug
Two-Pole Means That the Device Plug is Not Earthed And it Normally Has Two Pins That Transmit Electricity. Originally, all Electrical Devices Were Fitted With 2-Pole Plugs, Which Means That The Devices Were not Earthed and That all Main Sockets were Constructed for 2-Pole Plugs 2-Pin Plugs Consisting of Two flat or Round Pins With one Called “hot”. When Connected to an Electric Circuit, the Current Flows From the live Pins Through the Copper Conductor And into the Device. These Appliances do not Rely on The 'Earth' Wire for Protection From a Short Circuit and Therefore Only 2 Pins are Needed – one for The 'Live' Wire and The Other for The 'Neutral' Wire.

Thank You for visiting the website. Keep visiting for more Updates.

Post a Comment

Do leave your comments

Previous Post Next Post



Blogging Experiment
Electronic Experiment Subscribe our Youtube Channel