Power Socket Wiring Diagram

Power Socket wiring diagram:

This diagram shows how to make Power Socket Wiring Diagram. In this circuit, we use two FP MCBs ( Four Pole Minature Circuit Breakers), some DP MCBs  ( Double Pole  Minature Circuit Breaker ), and a power socket. First, we need to connect the MCB 1 with the power source, then connect the differential switch with the MCB, then connect all MCB circuit breakers and then connect the power socket.

Diagram of Power socket wiring:

Fig 1: Power Socket Wiring Diagram

Components Need for this Project:

You can get the components from any of the sites below:

1. FT MCB [See Buy Click Amazon]
2. RCCB [See Buy Click Amazon]
3. DP MCB [See Buy Click Amazon]
4. Power Socket [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

$ads={1}

Read Also:

• single phase motor wiring diagram

• Pump Motor Control Wiring

• single phase pump motor wiring

• Single Phase Pump Motor Starter WiringSingle Phase Pump Motor Starter Wiring

• single phase SDB connection for House wiring

Components used to make the 3 phase Socket wiring:

01. FT MCB

Fig 2: FT MCB

Four pole MCCB for Four wires connections, the one additional Four pole for neutral wire connection so that between neutral and any of the other three will supply. It is used where is the possibility of a high neutral current (due to unbalanced loads and /or Third and multiple Third harmonics current etc) and Neutral / Earth Protection is provided on Neutral. Four Pole Circuit Breakers Have advantages in the case When one of the Poles of the Device will get Damaged, and they also provide Isolation from neutral voltage.

02. RCCB 

Fig 3: RCCB

The RCCB (Residual Current Circuit Breaker) or RCCB is an electrical protective device. A residual Current Circuit Breaker is specially designed to protect the electrical circuit against earth faults and humans from electrical shock. In this, under normal conditions the load is always connected between the phase terminal to the neutral terminal, hence the flow of the phase current is equal to the neutral current. Earth fault or fault in a power system can cause excess heating, more power consumption, burning or fire, etc. So, protection against earth leakage is very important.

03. DP MCB

Fig 4: DP MCB

Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

04. Power Socket

Fig 5: Power Socket

A socket is a type of equipment used in electrical wiring lines that always has an electrical connection. According to the need, it can be supplied to the electrical equipment. In case of electric iron, electric hand drill machine and electric hand grinder etc. two-pin socket with earth terminal is used. Also, three-pin sockets are used for electrical appliances that have a metal body and are likely to be electrified. Eg – Refrigerator, room heater, table heater, hot-plate, electric oven etc.

Thank You for visiting the website. Keep visiting for more Updates.

$ads={2}

Frequently Asked Questions

How do you wire a plug with 3 wires?

Follow the steps for the terminal screw plug, but work with three wires instead of two. The black wire, which is hot and carries the Circuit diagram electricity, goes to the golden brass screw Power Supply. The white wire is neutral and hooks around the Currenttlou silver screw. The green wire goes to the Project system ground screw.

How does a power socket work?

The neutral is connected by a wire to the ground, so its voltage is 0 V. Instead, the hot slot supplies the Circuit diagram voltage required to draw current, and when a plug is inserted into the Circuit diagram socket, the energy flows in from the hot slot, through the circuit diagram, and ends at the neutral, which disperses the energy into the project system ground.

What color is the wire in a power socket?

See Table below. The protective ground is green or green with a yellow stripe Power Supply. The neutral is white, the hot (live or active) single-phase wires are black, Projec,t system, and red in the case of a second active. The 3-phase lines are red, black, and blue Circuit diagram.

What is inside a wall socket?

Plug sockets are made up of three main parts Circuit Diagram: A backbox (also called a pattress or mounting box power supply) can be recessed into a wall or mounted to a power supply surface. The electrical wiring is housed inside the Currenttlou backbox. A faceplate, which is screwed to the Circuit diagram backbox, acts as a lid.

How does a 3-wire plug work?

The rounded third prong on a plug is a ground prong or grounding Circuit diagram wire. Electricity is always looking for a path to the power supply ground. If damage or a malfunction occurs Project system, altering the circuit, the ground wire is an emergency path that the power supply protects you and your devices from electric shock.