Fluorescent Tube Light Wiring | Tube light connection

Fluorescent Tube Light Wiring:

The tube just needs a voltage. lamp's Electronic ballast a special sort of transformer wired into the circuit diagram. When the current flows through the bypass circuit diagram. it establishes a magnetic field in a part of the electronic ballast. If you want more clear details about this diagram please check our youtube video at the below post.

Diagram of Tube light connection:

Fig 1: Fluorescent Tube Light Wiring

Components Need for this Project:

You can get the components from any of the sites below:

1. Fluorescent Tube Light [See Buy Click Amazon]
2. Electronic Ballast Choke [See Buy Click Amazon]
3. Switch [See Buy Click Amazon]

*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!

$ads={1}

Read Also:

• Single Phase ATS Connection Building

• Single Phase Motor Changeover Connection

• Over Voltage and Under Voltage Protective Device

• corridor wiring circuit | Hallway wiring circuit

• Fan regulator connection | fan regulator direct connection

Components used to make the Tube Light wiring:

01. Fluorescent Tube Light

Fig 2: Fluorescent Tube

A fluorescent lamp, tube light, or rod light is a type of electric lamp that uses electricity to excite mercury vapor to produce light. These lamps are mainly used as an artificial source of light. When the mercury vapor inside a fluorescent lamp is excited with electricity, the mercury molecules emit short-wavelength ultraviolet light that hits fluorescent particles to produce visible light. Fluorescent lamps always require a ballast to control the flow of electrical energy inside the lamp, which is required by incandescent lamps.

02. Electronic Ballast Choke

Fig 3: Electric Ballast Choke 

The word Ballast means balancer. Some of the problems mentioned above are in lighting the tube light in the preheating method. Basically electronic ballast is prepared to eliminate this problem. As a result, the tube light switches on and lights up the house. The type of ballast through which this is done is called electronic ballast. Basically, the tube light system also ballast play the role of the balancer. It stabilizes the current and voltage. If a tube light is connected directly to the main line without this ballast, excessive current will flow through the tube light.

03. Switch

Fig 4: SPST Switch

A Single-Pole, Single-Throw (SPST) Switch. It's Got one Output and One Input. The Switch will Either be Closed or Completely Disconnected. SPSTs are Perfect for on-off Switching. They're also a Very Common Form of Momentary Switches. SPST Switches are Commonly Used in a Variety of Electrical Circuits and Applications, Such as Turning on And off Lights, Fans, and Other Appliances. They can Also be Used to Control the Flow of Electricity to Different Parts of a Circuit or to Switch Between Different Circuits Altogether.

Thank You for visiting the website. Keep visiting for more Updates.

$ads={2}

Frequently Asked Questions

Is tube light and fluorescent light the same?

LED tube lights are increasingly power supply used to replace fluorescent lights. Compared to fluorescents, LED lighting lasts longer, is more energy efficient, and uses no mercury. LED lights also offer superior light Circuit diagram quality, with no flickering. They also turn on immediately, without any warmup time required.

Do fluorescent lights use DC?

Fluorescent lamps can run directly from a power supply direct current (DC) supply of sufficient current voltage to strike an arc. The ballast must be resistive and would consume about as much power as the lamp.

Are tube lights fluorescent?

It's known for energy efficiency compared to Circuit diagrams incandescent and halogen light bulbs, and a lower price Circuit diagram compared to LEDs. There are several different types of fluorescent lighting power supply including linear fluorescent tubes, fluorescent bent tubes, fluorescent circline tubes, and CFL power supply (compact fluorescent lamps).

Can you mix LED and fluorescent tubes?

If you attempt to mix CFL and LED bulbs on the same fixture, they may not work properly and could even result in an electrical shock. If you need to replace a CFL bulb with an LED bulb, it's best to buy an LED replacement bulb specifically designed for use with CFL light fixtures.

How do you connect a tube bulb?

Take the new G13 tube light bulb and align the Circuit diagram pins on each end with the sockets of the light fixture. Gently push the bulb into the power supply sockets until it clicks into place. Turn on the power supply to the light fixture and test the Circuit diagram new bulb to make sure it is working power supply correctly.