One Motor Control With 2 Meter Connection | motor connection with a contactor

One Motor Control With 2 Meter Connection | motor connection with a contactor

One Motor Control With 2 Meter Connection:

This Diagram Shows Motor Control is Defined as The Process of Initiating, Directing, and Grading Purposeful Voluntary Movement. Shumway-Cook Has Defined Motor Control as The Ability to Regulate Mechanisms Essential to Movement. Motor Control Includes Reflexes as Well As Directed Movement. To Control Movement, The Nervous System Must Integrate Multimodal Sensory Information And Elicit The Necessary Signals to Recruit Muscles to Carry Out a Goal.

Diagram of One Motor Control With 2 Meter wiring:

One Motor Control With 2 Meter Connection
Fig 1: One Motor Control With 2 Meter Connection

Components Need for this Project:

You can get the components from any of the sites below:

  1. Magnetic Contactor [See Buy Click Amazon]
  2. Timer [See Buy Click Amazon]
  3. DP MCB [See Buy Click Amazon]
  4. Single Phase Motor [See Buy Click Amazon]
*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!


Read Also:

Components used to make the One Motor Control With 2 Meter:

01. Magnetic Contactor

Magnetic Contactor
Fig 2: Magnetic Contactor
A magnetic contactor is an electrical device used for load control, automation, and protection. It is much like a magnetic reel. However, relays are generally used for low power and voltage, on the other hand, when we think of high power, these heavy-duty contractors only come to mind. It basically works by switching the load on and off. It has 3 terminals whose inputs are denoted as L1, L2, L3, and outputs as T1, T2, and T3. The circuit of the load is made in automation mode or protection using auxiliary contacts. It has two types of terminals. 1) Normally Open (NO). 2) Normally Closed (NC)

02. Timer

Fig 3: Timer
Timer is a specialized type of clock used for measuring specific time intervals.An electromechanical cam timer uses a small synchronous AC motor turning a cam against a comb of switch contacts. This type of timer often has a friction clutch between the gear train and the cam, the cam can be turned to reset the time.A simple example of the first type is an hourglass. Working method timers have two main groups: hardware and software timers.Most timers give an indication that the time interval that had been set has expired.


03. DP MCB

Fig 4: DP MCB
Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.

04. Single Phase Motor

Single Phase Motor
Fig 5: Single Phase Motor
Single-Phase Induction Motor is Very Simple in Construction, Economical, Reliable, and Easy to Repair And Maintain. Due to all these advantages, it is widely used in vacuum cleaners, fans, centrifugal pumps, blowers, washing machines, etc. It can run only by supplying 1 phase current through this motor. The main two parts of this motor are Rotor and Stator. Among them, the rotating part is the Rotor and the stationary part is the Stator. Like all induction motors, a single-phase induction motor consists of two main parts, the stator, and the rotor.

Thank You for visiting the website. Keep visiting for more Updates


Frequently Asked Questions

What is 2 phase connection?

2-phase service is an obsolete style of electrical power distribution where 2 phases are provided that were 90° out of phase with each other. There were two line wires and one neutral, so a two-phase service was commonly a two-phase three-wire service.

What is a 2-phase meter?

A two-phase electricity supply is where you have 2 live (positive) feeds to your property and will therefore you will need 2 sensors for your energy monitor. 2 phase systems are sometimes used for multiple tariff supplies such as Economy 7.

Can I run 2 AC on a single phase?

Yes, you can use 2 split ACs on a single-phase meter, as long as the combined power consumption of both AC units does not exceed the maximum load capacity of the meter. It's important to consult with a qualified electrician to ensure that the electrical system can safely support the additional load.

Can you convert the 2 phase to the 3 phase?

It can be possible by splitting the 2 phases into 3 phases by adding a phase difference between a third separate phase. But doubt is if it will work for a longer period of time. Like in a ceiling fan, a capacitor is used to split the phase into two to generate rotational movement.

Can we use 2 phases?

You can very well use 2 phases. There are 2 modes of electricity transmission, High Voltage Direct Current (HVDC) and High Voltage Alternating Current (HVAC). HVDC has no phases because it is DC, HVAC has 3 phases.

Post a Comment

Do leave your comments

Previous Post Next Post



Blogging Experiment
Electronic Experiment Subscribe our Youtube Channel