Split ac indoor Outdoor wiring air conditioner:
This Diagram Shows The Two Units Are Connected by Insulated Tubes which Are Piped Through a small hole in The Wall. Split System Air Conditioners Consist of a Main Indoor Air Conditioning Unit And An Outdoor Unit That Both Connect Together. The Inside Unit Contains The Evaporator Coils And a Filter, Whereas The Outdoor Unit Is Home To The Condensing Coil, Fan, And Compressor.
Diagram of Split ac indoor Outdoor wiring air conditioner wiring:
 |
| Fig 1: Split ac indoor Outdoor wiring air conditioner |
Components Need for this Project:
You can get the components from any of the sites below:
- DP MCB [See Buy Click Amazon]
- Isolator Switch [See Buy Click Amazon]
- Outdoor AC [See Buy Click Amazon]
- Indoor AC [See Buy Click Amazon]
- DP Switch [See Buy Click Amazon]
- Junction Box [See Buy Click Amazon]
*Please note: These are affiliate links. I may make a commission if you buy the components through these links. I would appreciate your support in this way!
Read Also:
Components used to make the Split ac indoor Outdoor wiring air conditioner:
01. DP MCB
 |
| Fig 2: DP MCB |
Double pole MCB can control two wires. This circuit breaker is generally used in single-phase electric lines. Double pole MCB circuit breaker input has two wires supply two wires and an output. In a single-phase line, A double-pole MCB circuit breaker is used to give good production. This circuit breaker is provided through phase and neutral circuit breaker, it is very safe. This circuit breaker is preferred for home appliances. A DP MCB usually trips for 2 reasons 1. Overload 2. Short circuit.
02. Isolator Switch
 |
| Fig 3: Isolator Switch |
Isolators are usually operated in no-load conditions or offline. It has no special arc extinguishing system. Isolator is used in electrical sub-stations to isolate various devices like transformer from line in no-load or light load condition. Isolator is an off load device whereas circuit breaker is an on load device. That is, the isolator cannot be operated when there is a load whereas the circuit breaker automatically operates when there is a fault in the system. So the isolator can be operated only where the circuit is disconnected from the load. Isolator has no means of extinguishing the arc.
03. Outdoor AC
 |
| Fig 4: Outdoor AC |
One is an Indoor Unit And The Other is an Outdoor Unit. Evaporators are installed in indoor units and condensers are installed outdoors. So in this case the indoor unit will be inside your house and you can fit the outdoor unit into the outside wall or roof of your house. But one thing should be noted that there should be a lot of free space next to the outdoor unit. A little space is needed otherwise the heat cannot be radiated immediately. In this case, the pipeline between the indoor unit and the outdoor unit is routed through a small hole in your wall.
04. indoor AC
 |
| Fig 5: indoor AC |
One is an Indoor Unit And The Other is an Outdoor Unit. Evaporators are installed in indoor units and condensers are installed outdoors. So in this case the indoor unit will be inside your house and you can fit the outdoor unit into the outside wall or roof of your house. But one thing should be noted that there should be a lot of free space next to the outdoor unit. A little space is needed otherwise the heat cannot be radiated immediately. In this case, the pipeline between the indoor unit and the outdoor unit is routed through a small hole in your wall.
05. DP Switch
 |
| Fig 6: DP switch |
A Double Pole (or DP) Switch is a Switch That Controls 2 Circuits at the Same Time. They are Essentially 2 switches in one. In terms of Residential Switching, this Normally Means it Switches the live and Neutral at the same time. Double pole (DP) Switches are often used for Appliances that Require Heavy loads. Double pole (DP) switches can also be used as a Safety Shut-off for a Residential appliance. A DP Switch has two Connections to 2 Separate Circuits.
06. Junction Box
 |
| Fig 7: Junction Box |
A Junction Box is a Box in Which Conductors Wires are Split or Terminated. Where a 3-Phase Circuit is used for Single-Phase Loads a Junction Box is Provided at each piece of equipment and a Single-Phase Supply is Tapped. A Junction Box is a Box in Which Conductors and Wires are Split or Terminated. A Junction Box is an Enclosed Distribution Panel for the Connection Branching of one or more Electrical circuits. The Term Junction Box May Also be Used For a Larger item, such as a Piece of Street Furniture.
Thank You for visiting the website. Keep visiting for more Updates
Post a Comment
Do leave your comments